[Aug-2021] CIP Level 1 NACE-CIP1-001 Exam Practice Dumps
2021 NACE-CIP1-001 Premium Files Test pdf - Free Dumps Collection
NEW QUESTION 28
What is used to determine compressed air cleanliness?
- A. Profilometer
- B. Psychrometer
- C. Needle pressure gauge
- D. Blotter test
Answer: A
NEW QUESTION 29
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Permit coating to take place so as not to lose the blast
- B. Review the relevant standard with the Contractor
- C. Call your supervisor
- D. Shut the job down
Answer: B
NEW QUESTION 30
The most important factor resulting in improved job site safety is:
- A. Safety Enforcement
- B. Situational Awareness
- C. Engineering Controls
- D. Personal Protective Equipment
Answer: B
NEW QUESTION 31
To achieve consistently accurate results with ALL alt test equipment
- A. wear gloves when sampling.
- B. calibrate the instrument in the field.
- C. wash your hands before sampling.
- D. avoid placing the sample discs on a surface.
Answer: C
NEW QUESTION 32
The initial steel condition is important to the NACE Inspector because:
- A. It affects the final appearance after blasting
- B. The Inspector may have to reject the Steel
- C. If the steel is pitted more coating will be required
- D. Less abrasive is need if the mill Scale s gone
Answer: B
NEW QUESTION 33
Check abrasive blast pressure close to the
- A. compressor
- B. blast pot
- C. substrate
- D. blast nozzle
Answer: D
NEW QUESTION 34
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION 35
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. wet film thickness (WFT) measurement.
- B. dry film thickness (DEI) measurement.
- C. vial lest.
- D. blotter test for the presence of oil and water.
Answer: D
NEW QUESTION 36
The Inspector's Log Book is generally:
- A. Retained by the inspector upon project completion
- B. Submitted to the client upon project completion
- C. Shared with all parties upon project completion
- D. Shredded by the inspector upon project completion
Answer: A
NEW QUESTION 37
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. surface comparator
- C. replica tape
- D. needle pressure gauge
Answer: D
NEW QUESTION 38
Which is a component that supplies most of the features and functions of the material?
- A. pigment
- B. solvent
- C. binder
- D. additive
Answer: C
NEW QUESTION 39
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection and Non-destructive testing
- B. Visual inspection only
- C. Visual inspection, Non-Destructive and Destructive testing
- D. All types of inspection
Answer: A
NEW QUESTION 40
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. how the item was coated.
- B. when the coating will be reapplied.
- C. what materials were used.
- D. what items were coated.
Answer: A
NEW QUESTION 41
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks and just record the same readings as you have been getting
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks regardless
Answer: A
NEW QUESTION 42
Daily reports are important because:
Select All That Apply
- A. Management uses them to make personnel decisions.
- B. The information aids communication with supervisors.
- C. Inspectors rarely change on a project.
- D. the information impacts future projects.
Answer: A,B,D
NEW QUESTION 43
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION 44
An Inspector should change position when:
- A. The Owner can save some money by the change
- B. The Inspectors position is not the majority position
- C. The Inspector is convinced by verifiable facts
- D. Only when directed by the supervisor
Answer: C
NEW QUESTION 45
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Always handwritten
- C. Timely, accurate and concise
- D. Submitted before the end of the job
Answer: C
NEW QUESTION 46
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. perform additional tests secretly to ensure there are no other potential issues at the site
Answer: C
NEW QUESTION 47
The main responsibilities of the inspector are to
- A. observe and direct the work of the contractors.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. demonstrate to the contractor how to apply the coating.
Answer: B
NEW QUESTION 48
Dew point is the temperature at which
- A. humidity decreases
- B. the air is saturated.
- C. condensation occurs.
- D. water freezes.
Answer: C
NEW QUESTION 49
Whenever dissimilar metals must join, the most common practice is to
- A. provide anodic protection to prevent corrosion.
- B. avoid coating all connected dissimilar metals.
- C. provide cathodic protection to prevent corrosion,
- D. coat all connected dissimilar metals.
Answer: D
NEW QUESTION 50
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 100% of the specified maximum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: A
NEW QUESTION 51
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. telegraphing.
- B. transitioning.
- C. juxtaposing.
- D. monitoring
Answer: A
NEW QUESTION 52
Stripe coats are best applied by:
- A. High volume low pressure spray
- B. Airless spray
- C. Brush
- D. Conventional spray
Answer: C
NEW QUESTION 53
......
Get ready to pass the NACE-CIP1-001 Exam right now using our CIP Level 1 Exam Package: https://www.prepawayexam.com/NACE/braindumps.NACE-CIP1-001.ete.file.html
A fully updated 2021 NACE-CIP1-001 Exam Dumps exam guide from training expert PrepAwayExam: https://drive.google.com/open?id=1Cppm20OhawFRoWS4ULCX2pEfDCCg0_Uv